Traxxas Stampede 2WD XL-5 & VXL RC Trucks, Parts & Upgrades
Traxxas Stampede 2WD XL-5 VXL
Do you want something that’s race-ready yet still a great option for beginning model drivers or younger motorsports enthusiasts? If so, then you’re going to want the Stampede XL-5. It’s got a top speed of around 30 MPH measured in real rather than scale miles, so you can be sure that it’s going to offer a ton of real action without sacrificing a whole lot in terms of control.
In many ways, we consider the Traxxas Stampede line to be the original high-performance offload monster truck at the RC Superstore. Best of all, the stock performance figures of this vehicle can be upgraded through judicious use of aftermarket parts.
Traxxas Stampede 2WD Parts & Upgrades
While each of these models offers some serious scale horsepower, you’re eventually going to run into a situation where you might either want some replacement parts or you’re going to need to upgrade one of the underlying components. Perhaps you’ll want to start with a cooling fan or another component that includes comparable moving parts. Since these components rotate, you may want to keep a few extras on hand if you do any real hardcore driving. Motors themselves, however, are what most people are going to be looking into.
2WD Brushless Motors
Waterproof brushless motor assemblies are what makes the Stampede series so attractive. Motor brushes have to be periodically replaced on any design that makes use of them, but Stampede VXL brushless motor systems don’t require any such small parts to be installed. As a result, you can keep your vehicle running longer without having to worry about opening the physical motor housing and making adjustments. This is good news for anyone who wants to start investing in additional motors because they’re going to be seriously racing.
On top of a motor, you might want an extra battery.
Stampede LiPo Battery
Don’t get caught without the power you need to reach further destinations than you ever thought possible. Invest in an additional LiPo battery as well as NiMH/LiPo chargers so you can keep your vehicle out on the road longer. When your current pack runs down, swap it out for a fully charged one and then place it into this dock. It’ll convert mains line power into potential DC energy that your Traxxas model can use in its efficient LiPo batteries.
Stampede VXL
The Stampede VXL uses the Velineon brushless power system, which can push these trucks to over 65 MPH if you’re using LiPo power. Both the XL-5 and VXL trucks include a tri-mode speed controller that offers an optional training mode for those who are just learning to control a model that has this kind of performance. No matter what kind of driver you are, there’s something to appeal to you in these kits.
If you’re still not sure what kind of 2WD Traxxas truck might be right for you, then contact us online at the RC Superstore for more information.
-
HRAESC303T06Hot Racing Traxxas VXL-3s ESC Aluminum Heat Sink & High Velocity Fan
This is the Hot Racing Traxxas VXL-3s ESC Aluminum Heat Sink and High Velocity Fan. This is a great upgrade for all Traxxas VXL brushless vehicles, including the Slash 2WD VXL, Slash 4x4, Stampede 4x4 VXL, Stampede 2WD VXL, Rustler VXL, and Bandit VXL...$2349 -
HRAMH550TE06Hot Racing Heat Sink Cooling Fan (Blue) for Rustler, Stampede, Slash
This is the Hot Racing Blue Aluminum Heat Sink Cooling Fan for use on 540 and 550 brushed and brushless motors in vehicles like the Traxxas Rustler XL-5 and VXL, Stampede 2WD, Stampede 4x4, Slash 2WD, Slash 4x4, and more! The versatile two-piece heat...$1188 -
HRATRX15GPL06Hot Racing Power Up Slipper Eliminator for Slash 2WD & 4x4, Stampede 2WD & 4x4, Rustler, Bandit
This is the Hot Racing Power Up Slipper Eliminator for Traxxas Slash 2WD & 4x4, Stampede 2WD & 4x4, Rustler, Bandit, 1/10 Rally VXL, and Jato 3.3. This will work on the XL-5 brushed and VXL brushless versions of the electric trucks.FEATURES:- Eliminates...$1588 -
HRATE125Hot Racing Differential Spool Locker for Slash 2WD, Stampede 2WD, Rustler, Bandit, Raptor
This is the Hot Racing Differential Spool Locker for Traxxas Slash 2WD, Stampede 2WD, Rustler, Bandit, and Traxxas Ford Raptor Slash 2WD trucks. This part replaces the differential gears for a locked differential and is recommended for off-road use only...$1388 -
HRATRX15GSLHot Racing Carbon Fiber Long Slipper Clutch Pads - Use in place of Traxxas 5352 or 5552
These are the Hot Racing Carbon Fiber Long Slipper Clutch Pads with 25% more surface area than stock pads, for use in place of Traxxas 5352 or 5552 pads. These fit Traxxas Bandit, E-Maxx, E-Revo, Jato 3.3, Rally VXL, Revo 3.3, Rustler, Slash 2WD, Slash...$888 -
HRATRX15GX06Hot Racing Small Super Duty Slipper for Slash, Stampede, Rustler, Bandit, Jato
This is the Hot Racing Small Super Duty Slipper System with Pressure Plate, Hub, and Friction Pad for Slash 2WD, Slash 4x4*, Stampede 2WD, Rustler, Bandit, 1/10 Rally VXL*, Jato 3.3, and Stampede 4x4*. This will work on XL-5 brushed and VXL brushless...$2888 -
HRATE890HHot Racing 90T 48P Aluminum Spur Gear for Traxxas Stampede 2WD
This is the Hot Racing 90-Tooth 48-Pitch Hard Anodized Aluminum Spur Gear for Traxxas Slash 2WD, Stampede 2WD, Rustler, and Bandit. It will work with XL-5 brushed and VXL brushless trucks.FEATURES:- CNC machined 6061-T6 aluminum construction- Replaces...$2388 -
HRASTE250Hot Racing Hardened Steel 50T 0.8 Mod 32P Spur Gear for Slash 2WD, Stampede 2WD, Rustler, Bandit
This is the Hot Racing Hardened Steel 50-Tooth 0.8 Mod 32-Pitch Spur Gear for Traxxas Slash 2WD, Stampede 2WD, Rustler, Bandit, and Telluride vehicles. This gear is significantly smaller than stock, which will increase top speed over stock. It will...$2488 -
HRATE883HHot Racing 83T 48P Aluminum Spur Gear for Traxxas 2WD Slash, Stampede, Rustler, Bandit
This is the Hot Racing 83-Tooth 48-Pitch Hard Anodized Aluminum Spur Gear for Traxxas Slash 2WD, Stampede 2WD, Rustler, and Bandit. It will work with XL-5 brushed and VXL brushless trucks.FEATURES:- CNC machined 6061-T6 aluminum construction- Replaces...$2388 -
HRATD105X06Hot Racing Aluminum 105mm HD Big Bore Rear Shocks for Slash, Stampede, Rustler
These are the Hot Racing Aluminum 105mm HD Big Bore Shocks. These can be used on the rear of Traxxas Slash 2WD & 4x4, Stampede 2WD & 4x4, Rustler, and many other vehicles using 105mm shocks. These can be great for scale and rock crawler builds as well...$3499 -
HRATRX15GSHot Racing Carbon Fiber Slipper Clutch Pads - Use in place of Traxxas 5352 or 5552
These are the Hot Racing Carbon Fiber Stock Length Slipper Clutch Pads, for use in place of Traxxas 5352 or 5552 slipper pads. These fit Traxxas Bandit, E-Maxx, E-Revo, Jato 3.3, Rally VXL, Revo 3.3, Rustler, Slash 2WD, Slash 4X4, Slayer Pro 4X4,...$748 -
HRATE48G01Hot Racing Aluminum & Carbon Steering Bellcrank for 2WD Slash, Rustler, Bandit
This is the Hot Racing Aluminum and Carbon Fiber Steering Bellcrank for Traxxas Slash 2WD, Rustler, Stampede 2WD, and Bandit vehicles. This will fit XL-5 brushed and VXL brushless vehicles. It replaces Traxxas part 3743.FEATURES:- CNC machined 6061...$2449 -
HRASTE876Hot Racing Hardened Steel 76T 48P Spur Gear for Slash 2WD, Stampede 2WD, Rustler, Bandit
This is the Hot Racing Hardened Steel 76-Tooth 48-Pitch Spur Gear for Traxxas Slash 2WD, Stampede 2WD, Rustler, Bandit, and Telluride vehicles. It will work on XL-5 brushed and VXL brushless vehicles with proper adjustment.FEATURES:- CNC machined and...$2488 -
HRASTE886Hot Racing Hardened Steel 86T 48P Spur Gear for Slash 2WD, Stampede 2WD, Rustler, Bandit
This is the Hot Racing Hardened Steel 86-Tooth 48-Pitch Spur Gear for Traxxas Slash 2WD, Stampede 2WD, Rustler, and Bandit vehicles. This will fit XL-5 brushed and VXL brushless trucks.FEATURES:- CNC machined and lightened hardened steel construction-...$1898 -
HRASSXS4680Hot Racing Hardened Steel Pinion Gear Set - 24T 26T 28T 30T - 48P, 1/8 Bore
This is the Hot Racing Hardened Steel 48-Pitch 1/8" Bore Pinion Gear Set. This set includes a 24-tooth, 26-tooth, 28-tooth, and 30-tooth pinion gear.This set of gears is great for Traxxas Rustler XL-5, VXL, Stampede 2WD, Slash 2WD, HPI Savage XS, and...$1888 -
HRACSG1827Hot Racing 27-Tooth 48P Hardened Steel 1/8 Bore Pinion Gear
This is the Hot Racing 27-Tooth 48-Pitch Hardened Steel 1/8 Bore Pinion Gear. This will fit many different vehicles. A few of them are listed below.FEATURES:Standard 4140 steel and heat treatedHeavy duty 4mm set screw for brushless powerYOU WILL...$544 -
RRP8714Robinson Hard Steel 14T Pinion - 5mm Bore 0.8 Mod (31.75P)
This is the Robinson Racing Extra Hard Steel 14-Tooth 0.8 Mod Pinion Gear with 5mm Bore. This is a perfect upgrade for use on motors with a 5mm shaft in vehicles like the Traxxas Slash 4x4, Stampede 4x4, E-Revo Brushless, E-Maxx Brushless, and Summit...$849 -
RRP8724Robinson Extra Hard 5mm Bore 24T Pinion 0.8 Mod (31.75P)
This is the Robinson Racing Extra Hard 24-Tooth 0.8 Mod (31.75P) Pitch Pinion Gear with a 5mm Bore. This is a perfect upgrade for use on motors with a 5mm shaft in vehicles like the Traxxas Slash 4x4, Stampede 4x4, E-Revo Brushless, E-Maxx Brushless,...$849 -
HRATD100X06Hot Racing Aluminum 100mm HD Big Bore Rear Shocks for Slash, Stampede, Rustler
These are the Hot Racing Blue Aluminum 100mm HD Big Bore Rear Shocks for Slash 2WD, Slash 4x4, Stampede 2WD & 4x4, Rustler, Bandit, T-Maxx and E-Maxx front/rear, Associated SC10, and many other vehicles that can use 100mm shocks. These are also a great...$2849 -
HRATE892HHot Racing 92T 48P Aluminum Spur Gear for Traxxas 2WD Slash, Stampede, Rustler, Bandit
This is the Hot Racing 92-Tooth 48-Pitch Hard Anodized Aluminum Spur Gear for Traxxas Slash 2WD, Stampede 2WD, Rustler, and Bandit. It will work with XL-5 brushed and VXL brushless trucks.FEATURES:- CNC machined 6061-T6 aluminum construction- Replaces...$2388 -
RRP8720Robinson Extra Hard 5mm Bore 20T Pinion 0.8 Mod (31.75P)
This is the Robinson Racing Extra Hard 20-Tooth 0.8 Mod (31.75P) Pitch Pinion Gear with a 5mm Bore. This is a perfect upgrade for use on motors with a 5mm shaft in vehicles like the Traxxas Slash 4x4, Stampede 4x4, E-Revo Brushless, E-Maxx Brushless,...$849 -
HRANSG820Hot Racing 20-Tooth 48P Nitride Steel Pinion Gear 5mm & 1/8 Shafts
This is the Hot Racing 20-Tooth 48-Pitch Nitride Steel Pinion Gear for 5mm and 1/8" Shafts. The pinion has a 5mm bore and also includes a 1/8" shaft conversion sleeve. This works on vehicles like the Traxxas Slash 2WD, Stampede 2WD, Rustler, as well as...$1288 -
RRP8712Robinson Steel 12T Pinion - 5mm Bore 0.8 Mod (31.75P)
This is the Robinson Racing Extra Hard Steel 12-Tooth 0.8 Mod Pinion Gear with 5mm Bore. This is a perfect upgrade for use on motors with a 5mm shaft in vehicles like the Traxxas Slash 4x4, Stampede 4x4, E-Revo Brushless, E-Maxx Brushless, and Summit...$849 -
RRP8713Robinson Steel 13T Pinion - 5mm Bore 0.8 Mod (31.75P)
This is the Robinson Racing Extra Hard Steel 13-Tooth 0.8 Mod Pinion Gear with 5mm Bore. This is a perfect upgrade for use on motors with a 5mm shaft in vehicles like the Traxxas Slash 4x4, Stampede 4x4, E-Revo Brushless, E-Maxx Brushless, and Summit...$849 -
RRP8711Robinson Steel 11T Pinion - 5mm Bore 0.8 Mod (31.75P)
This is the Robinson Racing Extra Hard Steel 11-Tooth 0.8 Mod Pinion Gear with 5mm Bore. This is a perfect upgrade for use on motors with a 5mm shaft in vehicles like the Traxxas Slash 4x4, Stampede 4x4, E-Revo Brushless, E-Maxx Brushless, and Summit...$849 -
HRASTE90MR128Hot Racing Front Multi-Rate Springs (3 Pairs) for Slash 2WD, Stampede 2WD, Rustler
These are the Hot Racing Front Multi-Rate Springs (3 Pairs) for Traxxas Slash 2WD, Stampede 2WD, and Rustler trucks. These will work on the XL-5 brushed and VXL brushless trucks.FEATURES:Spring Steel ConstructionMulti-Rate Springs, Dual-Rate (DRS) allow...$1488 -
RRP8722Robinson Extra Hard 5mm Bore 22T Pinion 0.8 Mod (31.75P)
This is the Robinson Racing Extra Hard 22-Tooth 0.8 Mod (31.75P) Pitch Pinion Gear with a 5mm Bore. This is a perfect upgrade for use on motors with a 5mm shaft in vehicles like the Traxxas Slash 4x4, Stampede 4x4, E-Revo Brushless, E-Maxx Brushless,...$849 -
RRP8718Robinson Extra Hard 5mm Bore 18T Pinion 0.8 Mod (31.75P)
This is the Robinson Racing Extra Hard 18-Tooth 0.8 Mod (31.75P) Pitch Pinion Gear with a 5mm Bore. This is a perfect upgrade for use on motors with a 5mm shaft in vehicles like the Traxxas Slash 4x4, Stampede 4x4, E-Revo Brushless, E-Maxx Brushless,...$899 -
HRATRX15EPHot Racing HD Aluminum Slipper Plate & Hub for Stampede, Slash, Rustler, Bandit, Jato
This is the Hot Racing HD CNC Machined Hard Anodized Aluminum Slipper Plate and Hub for the 1/10 Traxxas Bandit, Jato 3.3, Rally*, Rustler, Slash 2WD, Slash 4X4*, Stampede 2WD, and Stampede 4X4*. This item is a replacement for Traxxas 5556.*For high...$1488 -
HRASTE100MR128Hot Racing Rear Multi-Rate Springs (3 Pairs) for Slash 2WD, Stampede 2WD, Rustler
These are the Hot Racing Rear Multi-Rate Springs (3 Pairs) for Slash 2WD, Stampede 2WD, Rustler. These work on the rear of the XL-5 brushed and VXL brushless versions of these trucks.FEATURES:- Spring steel construction- Multi-rate springs allow the...$1388 -
HRACSG1831Hot Racing 31-Tooth 48P Hardened Steel 1/8 Bore Pinion Gear
This is the Hot Racing 31-Tooth 48-Pitch Hardened Steel 1/8 Bore Pinion Gear. This will fit many different vehicles. A few of them are listed below.FEATURES:CNC Machined light weight Precision Gears with Standard 4140 steelReduce internal rotating mass...$788 -
RRP8716Robinson Extra Hard 5mm Bore 16T Pinion 0.8 Mod (31.75P)
This is the Robinson Racing Extra Hard 16-Tooth 0.8 Mod (31.75P) Pitch Pinion Gear with a 5mm Bore. This is a perfect upgrade for use on motors with a 5mm shaft in vehicles like the Traxxas Slash 4x4, Stampede 4x4, E-Revo Brushless, E-Maxx Brushless,...$849 -
HRATE1006SLHot Racing Blue Aluminum 12mm Clamping Wheel Hexes for Slash 2WD, Stampede 2WD, Rustler
These are the Hot Racing Blue Aluminum 12mm Clamping Wheel Hexes for the front and rear of Traxxas Slash 2WD, Stampede 2WD, and Rustler trucks. These will fit XL-5 brushed and VXL brushless versions.FEATURES:- CNC machined aluminum, anodized blue-...$1688 -
HRASTE100MR08Hot Racing Rear Multi-Rate Springs for Slash, Stampede, Rustler
This is the Hot Racing Rear Multi-Rate Springs for Slash 2WD, Stampede 2WD, and Rustler trucks. These work on the XL-5 brushed and VXL brushless versions of these vehicles.FEATURES:Spring steel constructionMulti-rate springsDual-rate (drs) allow the...$3 -
RRP8717Robinson Extra Hard 5mm Bore 17T Pinion 0.8 Mod (31.75P)
This is the Robinson Racing Extra Hard 17-Tooth 0.8 Mod (31.75P) Pitch Pinion Gear with a 5mm Bore. This is a perfect upgrade for use on motors with a 5mm shaft in vehicles like the Traxxas Slash 4x4, Stampede 4x4, E-Revo Brushless, E-Maxx Brushless,...$849 -
RRP8715Robinson Extra Hard 5mm Bore 15T Pinion 0.8 Mod (31.75P)
This is the Robinson Racing Extra Hard 15-Tooth 0.8 Mod (31.75P) Pitch Pinion Gear with a 5mm Bore. This is a perfect upgrade for use on motors with a 5mm shaft in vehicles like the Traxxas Slash 4x4, Stampede 4x4, E-Revo Brushless, E-Maxx Brushless,...$849 -
HRASTE04HPHot Racing Traxxas Hardened Chrome Plated King Pin Set
This is the Hot Racing Traxxas Hardened Chrome Plated King Pin Set Hot Racing steel 2.5 x 31.5 mm Screw king pin set for Electric Slash 2WD, Rustler 2WD or Stampede 2WD FeaturesSpring Steel Screw 2.6 Pin for use in TRA 1/10 2WD Construction : CNC Harden...$285 -
HRATD90X06Hot Racing Aluminum 90mm Heavy Duty Big Bore Shocks (2pcs)
This is the Hot Racing Aluminum 90mm Heavy Duty Big Bore Shocks (2pcs) 90mm big bore threaded body aluminum shocks for many 1/10th scale off-road vehicles using 90mm shocks. Some applications include, but are not limited to: Traxxas Bandit front, Nitro...$2499 -
HRASSXS8024Hot Racing Chrome Steel Pinion Gear Set - 28T 30T 32T 34T - 48P, 1/8 Bore
This is the Hot Racing Chrome Steel Speed Tune 48-Pitch 1/8" Bore Pinion Gear Set. The set includes a 28-tooth, 30-tooth, 32-tooth, and 34-tooth pinion gear.Designed for use with stock HPI Savage XS idler gear. Also works on Traxxas vehicles requiring...$1888 -
HRACSG1826Hot Racing 26-Tooth 48P Hardened Steel 1/8 Bore Pinion Gear
This is the Hot Racing 26-Tooth 48-Pitch Hardened Steel 1/8 Bore Pinion Gear. This will fit many different vehicles. A few of them are listed below.FEATURES:Standard 4140 steel and heat treatedHeavy duty 4mm set screw for brushless powerYOU WILL...$544