This is the Traxxas 20-Tooth Transmission Input Gear and 2.5x12mm Pin. 20-tooth transmission input gear. Includes 2.5x12 mm dowel pin.Replacement Part ForX-MaxxXRT

These are the RC4WD Dick Cepek Mud Country Scale Tires with foam inserts for use with 1.9" wheels. The tires have a 3.95" outside diameter. These have been officially licensed by the Dick Cepek tire company.Features Advanced X3 Soft & Sticky...

This is the Traxxas Stub axle, rear, steel-splined constant-velocity (1)Replacement rear stub axle for Traxxas steel CV driveshafts (1951R, 6852R)Accessory Part For:BIGFOOTHoss 4X4 VXLNitro RustlerRustler 4X4 VXLRustler 4X4Rustler VXLRustlerSlash 2WD...

This is the Traxxas TQi 2.4GHz 2-Channel Radio System with 5-Channel Traxxas Stability Management (TSM) telemetry-enabled receiver included. Traxxas Stability ManagementTraxxas Stability Management (TSM) allows you to experience all the extreme power,...

These are the Traxxas Hardened Steel Front Driveshafts for the Traxxas 1/10 Scale Slash 4x4, Rally, and Stampede 4x4 vehicles. Traxxas Steel Constant Velocity Shafts offer the ultimate in torque handling and efficient power transfer. The outer U-joints...

This is a set of RPM Black Nerf Bars for the Traxxas Slash 2WD and Slash 4x4 standard chassis trucks. This will not fit trucks with a low-CG chassis (does not fit Slash Ultimate).Nerf bars play an extremely important function in the overall durability...

This is the Traxxas Maxx Chevron Tires with 3.8" Split Spoke Wheels Maxx Chevron tires are 3.8″ inches of soft compound rubber with a wide, low-profile design for excellent off-road handling and reduced weight. They come pre-glued to chrome...

This is a Traxxas T-Maxx (.15, 2.5, 2.5R, and 3.3) Primerless Fuel Tank.  This is the updated version.  This tank fits all of the nitro Maxx trucks, and there is no longer a primer on it, so you don't have to worry...

This is the Castle Creations Cobra 6, 33.6V, 8A Peak BEC ESC w/ 2028-800KV Sensored Motor COBRA 6 Racer Tested - Basher ApprovedThe COBRA 6, 33.6V ESC W/2028-800KV SENSORED COMBO is ready to take on any R/C vehicle weighing up to 25lbs and running up to...

This is the Viper Scale Racing (YELLOW BODY) Alky Funny Car Ready to Race HO Slot Car The Alky Funny Car is a high performance Slot car built specifically for Drag racing. This car packs lots of High performance features V1 High performance Chassis Pro...

This is the Viper Scale Racing (BLUE BODY) Alky Funny Car Ready to Race HO Slot Car The Alky Funny Car is a high performance Slot car built specifically for Drag racing. This car packs lots of High performance features V1 High performance Chassis Pro 10...

This is the Viper Scale Racing (RED BODY) Alky Funny Car Ready to Race HO Slot Car The Alky Funny Car is a high performance Slot car built specifically for Drag racing. This car packs lots of High performance features V1 High performance Chassis Pro 10...

This is the Castle Creations Cobra 8, 25.2V ESC with 1512-1800kV Sensored Motor Combo Cobra 8, 25.2V ESC with 1512-1800kV Sensored Motor ComboCapable of 2S to 4S LiPo and ready to overpower 1:8th scale off-road and on-road vehicles as well as 1:10 scale...

This is the Castle Creations Sidewinder SW4 Waterproof ESC and 1410-3800Kv Brushless Motor Combo with 5mm Motor Shaft. This combo is a great setup for 2S power in vehicles like the Traxxas Slash 2WD and 4x4, or up to 3S in the 2WD Rustler, Bandit and...

This is the Castle Creations Sidewinder SW4 Waterproof ESC and 1410-3800Kv Brushless Motor Combo with 1/8" (3.17mm) Shaft. This combo is a great setup for 2S power in vehicles like the Traxxas Slash 2WD and 4x4, or up to 3S in the 2WD Rustler, Bandit and...

This is the Castle Creations Mamba X SCT Sensored 25.2V ESC with 1410-3800Kv Brushless Motor with 1/8" (3.17mm) shaft. This combo is a great setup for 2S power in vehicles like the Traxxas Slash 2WD and 4x4, or up to 3S in the 2WD Rustler, Bandit and...

This is the Castle Creations Mamba X Sensored 25.2V Waterproof ESC with 8-Amp BEC. Meet the next generation.Castle Creations is proud to announce our new flagship surface product, the MAMBA X EXTREME 1:10 SCALE WATERPROOF ESC. We at Castle wanted to...

This is the Castle Creations 1/8 Mamba Monster X 2S-6S ESC with 8-Amp BEC. Putting the X in Extreme!Mamba Monster X is our latest 1:8 scale and Monster truck controller capable of 2S - 6S LiPo, with an 8 amp peak BEC - and, it's waterproof*, so you can...

This is the Castle Creations Sidewinder SCT Waterproof ESC and 1410-3800kv Brushless Motor with 1/8" (3.17mm) Shaft. This setup is intended for 1/10 short course trucks running on 2s LiPo and weighing up to 6.5 lbs. It is also a great system and a torque...

This is the Castle Creations Sidewinder SV3 Waterproof ESC & 1406-5700Kv Brushless Motor with 1/8" (3.17mm) shaft. The 1406-5700kv motor is a great motor for 2WD short course trucks on 2s LiPo and geared conservatively. It makes a great combo for...

This is the Castle Creations Sidewinder SV3 Waterproof ESC and 1406-4600Kv Brushless Motor with 1/8" (3.17mm) shaft.  The 4600kv motor is a great motor for 2WD short course trucks on 2s LiPo and geared conservatively. It makes a great combo for...

This is the Castle Creations Sidewinder 4 Sensorless Waterproof ESC for brushed or brushless motors on 2-3S LiPo or 6-8 cell NiMH power. While the all new SIDEWINDER 4 builds upon Castle's most popular platform, the SIDEWINDER 1:10 SCALE SERIES, it is...

This is a set of GPM Racing Green Aluminum 17mm Wheel Nuts for Traxxas X-Maxx and E-Revo 2.0 trucks. This is a full set of four nuts.These fit in place of stock Traxxas part 7758 series wheel nuts.Accessory Part ForTraxxas 1/10 E-Revo 2.0Traxxas...

These are the Traxxas E-Revo 2 Heavy Duty Toe Link Rod Ends (8) with Hollow Balls.Stock Replacement OnE-Revo 2.0

These are the Traxxas Unlimited Desert Racer Steel Hex Wheel Hubs (4).Accessory Part ForUnlimited Desert Racer (UDR)

This is the Tekin RX8 Gen3 Brushless 1/8 Scale Dual Mode ESC (Sensored/Sensorless). Tekin's RX8 GEN3 brings bigger power handling capabilities and increased reliability to 1/8 Scale Racing. The RX8 platform has proven itself to handle the rigors of...

This is the Hot Racing Small Super Duty Slipper System with Pressure Plate, Hub, and Friction Pad for Slash 2WD, Slash 4x4*, Stampede 2WD, Rustler, Bandit, 1/10 Rally VXL*, Jato 3.3, and Stampede 4x4*. This will work on XL-5 brushed and VXL brushless...

This is a pair of Traxxas X-Maxx Replacement Upper Suspension Arms. These will work on the front or rear of the truck.FeaturesMolded composite plastic constructionFits both front and rear suspensionIncludes: One Left and One Right Upper Suspension Arm

This is the RPM Black Extended Right Rear A-Arm Set for 1/10 Summit (stock replacement), E-Revo 2.0 (stock replacement), 1/10 E-Revo, E-Revo Brushless, and Revo 3.3 trucks. These are replacements for Traxxas part 5333R or 8631. See Tech Notes at...

These are the RPM Black Extended Left Rear A-Arms for 1/10 Summit (stock replacement), E-Revo 2.0 (stock replacement), 1/10 E-Revo, E-Revo Brushless, and Revo 3.3 trucks. These are replacements for Traxxas part 5333R or 8632. See Tech Notes at bottom for...

These are the RPM Heavy Duty Blue Rear A-Arms for the Traxxas Electric Slash 2WD Short Course Racing Truck. The RPM rear A-arms for the Traxxas Slash 2WD are designed specifically for the electric version of the Slash. They are molded in RPM's nearly...

This is the RPM True-Track Rear A-Arm Conversion (Black) for the Traxxas T-Maxx 3.3 and E-Maxx 16.8V (model 3905), and E-Maxx Brushless trucks.  The RPM True-Track Rear A-arm Conversion kit eliminates one of the biggest headaches...

This is a Traxxas M0.8P, 50T Spur Gear. FEATURES M0.8 pitch 50 tooth Black plastic construction Compatible with 32P pinion gears INCLUDESOne M0.8P, 50T Spur Gear SPECSPitch:   M0.8Tooth:   50Outer Diameter: 41.5mm (1.63")Inner...

This is a pair of Stub Axle Carriers for the Traxxas Bandit, Stampede and Rustler VXL. FEATURES:Molded nylon construction (black) INCLUDES:Two stub axle carriers REQUIRES:Installation on the vehicle

This is a Traxxas Jato 2.5, 3.3, and T-Maxx 3.3 Antenna Crimp Nut and Antenna Nut Wrench.  This includes the antenna crimp nut and the wrench.

This is a Traxxas 37-Tooth Ring and 13-Tooth Pinion Gear Set for the Traxxas T-Maxx .15, 2.5, 2.5R, 3.3 (model 4909 only), and E-Maxx (model 3906 only).  The differential carrier is also included. FEATURES:Replaces worn differential...

This is the Viper Scale Racing Viper Jet w/ V17 Blue Body Viper Jet The Viper Jet is based on the highly popular and successful V1 platform with the addition of CNC machined brass weights. This car is designed to be run on 12 or 18 volts and packs a ton...

This is the Viper Scale Racing Viper Jet w/ V17 Yellow Body Viper Jet The Viper Jet is based on the highly popular and successful V1 platform with the addition of CNC machined brass weights. This car is designed to be run on 12 or 18 volts and packs a...

This is the Pro-Line Rat Rod Clear Body for Traxxas 1/10 Revo 3.3, E-Revo, E-Revo 2.0 and Summit trucks. The body is supplied clear, but is painted in the image to better show the design. Truck is not included. FeaturesCustom Rat Rod stylingScale...

These are the RPM Black Front Left Suspension A-Arms for Traxxas E-Revo 2.0 trucks. While Traxxas may have beefed up the E-Revo 2.0 suspension arms, they’re still not nearly as tough as RPM versions, nor are they as light. RPM A-arms weigh in 5 grams...