These are Traxxas 4x8x3mm Sealed Ball Bearings (2). These are used in 1/16 vehicles such as the E-Revo and Slash, as well as many other Traxxas vehicles. Features:Blue rubber sealedMay also be used in any vehicle where this size bearing is...

This is a Team Integy Aluminum Motor Heatsink with Cooling Fan (Purple) for the Traxxas Slash 2WD, Stampede 2WD, Rustler and Bandit vehicles. This will only fit XL-5 versions.Heat is the enemy, especially when it comes to electric motors. Keep your...

This is the E-flite 30-Amp Pro V2 Switch-mode BEC Brushless ESC. This is a high-quality sensorless brushless electronic speed control with an integrated switch-mode BEC that is very lightweight and efficient. It can operate without the need for a...

This is the Blade Rotor Head Linkage Set (4) for the Blade Nano CP X helicopter (nCP X)

This is the Temperature and Voltage Sensor for the XO-1 On-Road Car from TraxxasFeaturesFunctions with the Traxxas TQi Link system to display battery voltage and temperature.IncludesTemperature and Voltage Sensor with Zip Tie.

This is the Blade mCP X Helicopter Main Rotor Hub with Hardware

These are the Traxxas Front and Rear Toe Links for use on the 1/16 Slash and E-Revo vehicles. Features: Nylon construction Red in color Includes:Two Front and two Rear Toe LinksEight Hollow Balls Specifications:Length: 67mm (2.6")Diameter: 5mm (0...

These are the Traxxas Pushrods for use on the 1/16 Slash VXL 4WD. Features: Nylon construction Red in color Includes:Four PushrodsEight Hollow Balls Specifications:Length: 55mm (2.2")Diameter: 5.2mm (0.20")

These are Traxxas 2.5x8mm Cap Head Screws (6). Features: Steel construction Black in color Cap head design Includes: (6) 2.5x8mm cap head screws Specifications:Length: 5/16" (8mm)Diameter: 3/32" (2.5mm)

This is the Traxxas 27mHz Two Channel AM Receiver without BEC. 2-channel 27MHz receiver without BEC (for use with electronic speed control) Features: Mounting tabs on either side insure secure attachment to chassis. Includes: One Two Channel...

This is the Robinson Racing Xtra Hard Steel 18-Tooth Pinion Gear with a 5mm shaft hole.  This is perfect for use on the Traxxas Revo and E-Maxx when running electric motors with a 5mm shaft. Features: Extra hardened steel...

This is the Blade Hardware Set BLH3122 Blade 120SR

This is the E-Flite Feathering Spindle w/ O-rings and Bushings: 120SR

This is the Carrier Differential for the Traxxas Revo and E-Maxx. FEATURES Replaces worn diff carriers gaskets and spacers INCLUDESDiff Carrier and GasketsSteel Spider Gear Braces (not used with Revo)Instruction sheet REQUIRESDisassembly of...

This is a pair of Traxxas 2.8" Black Chrome All Star Wheels mounted with Talon Tires. Talon tires provide "just-right" grip and handling on a wide variety of surfaces. The tires come mounted with foam inserts and pre-glued to tough 2.8″ All-Star...

This is a Package of Replacement Cush-Drive Elements for the EZ Start 2 System. FEATURES:Black plastic construction INCLUDES:Four cush-drive elements REQUIRES:The remainder of the EZ Start 2 system. SPECS:Length: 6mm (0.24")

This is the optional .8 Metric Pitch 65 Tooth Spur Gear for the Traxxas E-Maxx. FEATURES:Nylon construction, black in color.8 metric pitch INCLUDES:One 65T 0.8 metric pitch spur gear REQUIRES:Installation on the vehicle SPECS:Diameter: 2.12"...

This is the Wing Mount for the Traxxas Revo 3.3 FEATURES:Nylon ConstructionBlack in Color INCLUDES:Two Wing SupportsOne Wing MountFour 4mm x 8mm Cap Head Socket ScrewsFour 3mm x 12mm Cap Head Socket ScrewsOne Instruction Sheet REQUIRES:Installation

This is a Traxxas Jato 2.5 and 3.3 Complete Fuel Tank Assembly.  This direct replacement tank features clear nylon construction with spring loaded lid, pre-installed pressure fittings, and the tank lid has a pull ring for easier refuelling. ...

This is a Traxxas Jato 2.5 and 3.3 E-Z Start Wiring Harness.  This is a direct replacement part.

This is an 18 Meter Roll of 18mm Tamiya Masking Tape. Features: This is a thin, self-adhesive paper tape, developed for model applications Flexible Easily applied to curved surfaces making it ideal for masking off areas for painting, etc. Comes in a...

This is the Dynamite Metric Driver Set.  This set includes a 1.5, 2, and a 2.5mm wrench.  These hardened steel-tipped tools will last a long time. Their comfortable-grip anodized handles are flat on one side so they won't roll off the...

This is a set of four (4) Deans 2-Pin Female Ultra Plug wire connectors.  These low-resistance, compact-size 2-Pin Ultra Plug Connectors from Deans provides a secure connection for battery and motor connections on R/C vehicles...

This is the Traxxas Front, Mid-Front, and Rear Skid Plate set for the Revo 3.3, 1/10 E-Revo, and Slayer trucks.IncludesFront, mid-front, and rear skid plates(8) 3X10mm button head screws(1) 3X30mm button head screwsFits1/10 E-Revo Brushed1/10 E-Revo...

This is the Traxxas Front Bulkhead for the Revo and Slayer. Features: Black plastic construction Rocker shafts preinstalled Includes:Front bulkhead halves(2) rocker shafts(4) 4X14mm button head screws

This is a pair of Traxxas Steel Pushrods with installed rod ends for use with Progressive 1 Rockers or long travel rockers. If you need the rockers too, search our store for TRA5357. If you would like to replace the front and rear pushrods, purchase a...

This is a Traxxas TRX 2.5 and 2.5R Piston and Sleeve kit.  If you have several gallons of fuel through your engine, it may be time for a new piston and sleeve.  It is a direct replacement.  Included are one piston, one...

This is the Stock Replacement Diff Gear Set for the Traxxas T/E Maxx.  These gears can also be referredto as bevel gears. FEATURES:Durable steel construction INCLUDES:Two 13 Tooth Output Gear ShaftsTwo 13 Tooth Spider GearsOne Spider ShaftOne 6x10x0...

This is the Front Skidplate for the Traxxas T-Maxx Monster Truck. This skidplate bolts to the Chassis (key #4922) and the Bulkheads key #4930 and provides protection to the front differential. FEATURES:Skidplate is constructed of high impact molded black...

This is the Pro-Line 1/16 Pre-Cut Brute Clear Body for the Mini Maxx The Brute Clear Body for the Traxxas Mini Maxx is more than just a replacement body. It is your chance to build something completely your own. From clean race inspired paint schemes to...

This is the Traxxas TRX-4M Chevrolet K10 Black Body Is it time to replace your TRX-4M High Trail Edition body or upgrade to an all new look? TRX-4M High Trail Edition clipless bodies come ready to mount on your High Trail truck right out of the bag...

This is the Traxxas TRX-4M Ford F-150 Brown Body Is it time to replace your TRX-4M High Trail Edition body or upgrade to an all new look? TRX-4M High Trail Edition clipless bodies come ready to mount on your High Trail truck right out of the bag...

This is the Traxxas TRX-4M Chevrolet K10 Unpainted Body Kit Give your TRX-4M High Trail Edition a custom look with this white ChevroletK10 body. You choose the color and design and Traxxas ProGraphix paint makes it easy to get professional quality...

This is the Pro-Line 1/10 Rock Shooter Aluminum Front/Rear 1.9" 12mm Crawling Wheels (2) Rock Shooter Aluminum Crawling WheelsThis is a pair of Rock Shooter 1.9" Aluminum Composite Internal Bead-Loc Wheels. Pro-Line is proud to introduce the Rock Shooter...

This is the Scaleauto Advertising Billboard Panel Scaleauto Scenics CollectionAdvertising Panel measuring 200x75mm for SC-10234 or SC-10235 supports (Type A and B) RequiresBillboard Supports Sold Separately. Works with SC-10234 or SC-10235...

This is the Traxxas 26-Tooth Pinion Gear (32-pitch) 3mm Bore 26-tooth pinion gear (32 pitch) fits 3 mm motor shafts and includes set screw. Traxxas pinion gears let you fine-tune the performance of your Traxxas model. Changing gear ratios can help...

This is the Traxxas Mini GTR Short TiN-Coated Shock Shafts (2) These hardened-steel shafts for short Mini GTR shocks have a super tough titanium nitride coating with a micro-polished finish that reduces stiction for smoother performance and resists...

This is the GPM TRX-4m Land Rover Defender D90 and D110 Metal Camping Table The cover can be opened, simulation tools and tableware can be placed. The main body is finished with stainless steel, matte black surface treatment, and the logo in hollow...

This is the GPM TRX-4m Ford Bronco Universal Metal Simulation Oil Tank and Exhaust Pipe Set IncludesMetal Simulation Oil Tank and Exhaust Pipe (one set/4 pieces) - 4pcsScrew - 17pcs Notes: Packaged in loose parts, need to install it yourself according to...

This is the GPM TRX-4m Land Rover Defender Rubber Mudguard and Metal Fixing Bracket Set The bracket is made of stainless steel and is more sturdy, with rubber mudguards. Installation in the beam holes of the original vehicle, suitable for TRX4M vehicle...