Jato 3.3

This is the Traxxas 2055 High-Torque Servo.  This has 80 oz/in of torque, making it an excellent steering servo.  This works well in the Traxxas T-Maxx, E-Maxx, Revo or any other vehicle that you would like to mount this in...

This is a Traxxas 56-Tooth Spur Gear for the Jato 2.5, 3.3, and the T-Maxx 3.3. The lower number of teeth on the spur gear, the faster the vehicle will be.  The higher the number of teeth, the more acceleration it will have.

These are the Traxxas 2.5x10mm Cap-Head Hex Machine Screws. Each package includes six screws.Set of six 2.5x10 mm cap-head machine screws with hex-drive heads Replacement Part For:1/16 E-Revo VXL1/16 E-Revo1/16 Slash 4WD1/16 Summit4-Tec 2.0 AWD...

This is a set of RPM Black Snap-Tite Body Savers. One of the weakest points on a Lexan body is where the body mounts to the chassis. The holes cut in the body for the body posts have a tendency to crack and fracture. This is the reason RPM designed these...

This is the Traxxas Replacement O-ring Header Gasket for the Traxxas 2.5, 2.5R, and 3.3 Engines. This is located on the header of the engine. Features: Red silicone construction. Includes: One 12.2x1mm o-ring

This is the Traxxas TRX 3.3 Racing Engine with Pull Start.  This will give your Revo, T-Maxx 2.5, or Jato an unbelievable boost in performance.  This is a must have upgrade.  You can also use this with the factory EZ-Start. ...

These are the Wheelie Bar Wheels for the Traxxas 3.3 T-Maxx. FEATURES:Constructed of hard plasticAxles constructed of steel INCLUDES:Four wheels and two axles REQUIRES:Installing on wheelie bar SPECS:Thickness: 0.39" (10mm)Diameter:  1.02" (26.1mm)

This is a pack of Traxxas 3x15mm Countersunk Hex Head Machine Screws. Each package includes six screws.Fits:1/10 E-Revo Brushed1/10 E-Revo Brushless1/10 SummitE-MaxxE-Maxx BrushlessFunny CarJato 2.5Jato 3.3Nitro 4-TecRevo 3.3SlayerSlayer ProT-Maxx 2...

This is the Traxxas 35mm Flywheel with Magnet for use with the TQi Radio System.FeaturesFor use with Traxxas glow powered vehiclesEquipped with a magnet that enables an RPM sensor to read RPM data IncludesTraxxas 35mm Flywheel with Magnet

This is the Traxxas iD LiPo Battery Balance Adapter for Cell Voltage Checkers. This works with 2S, 3S, and 4S ID LiPo batteries to connect them to cell voltage checkers for individual cell reading. Warning: These are not intended for charging. The...

This is the Traxxas High-Speed Needle Valve Assembly for the TRX 2.5, 2.5R, and 3.3 nitro engines. This includes the high speed need, fuel fitting, 2.5x1.15mm O-rings (2), and 5.3x7.8x.6mm crush washers (2).For use with TRX 2.5 & 3.3 engines used...

These are the Traxxas 3x15mm Buttonhead Hex Machine Screws. Each package includes six screws. These are used across many different Traxxas vehicles.Replacement part for1/16 E-Revo VXL1/16 E-Revo1/16 Slash 4WD1/16 Summit4-Tec 2.0 AWD Chassis4-Tec 2.0 VXL...

This is a set of six Traxxas 4mm x 10mm Countersunk Machine Screws for the Jato 2.5 and 3.3 trucks. Replacement part for these modelsJatoMaxxNitro SlashX-MaxxXRT

This is a pair of Traxxas 5x11x4mm ball bearings.  These are used in the clutch bells of many of the Traxxas vehicles. Features:Ball bearings reduce friction and last longer than bushings.Chrome steel construction.Used to upgrade from...

These are the RPM Green Long Rod Ends (12) for 1/10 Traxxas vehicles. These are direct replacements for TRA5525 rod ends.RPM Rod Ends cover a wide range of currently available Traxxas vehicles including all versions of the following: Slash 2wd, Slash...

This is the Traxxas ProGraphix Body with Decals for the Jato 3.3. Features Graphics are printed, requires paint & final color application Overview With the ProGraphix process, you will never see bleeding paint or over-sprays that need to be covered...

This is the Traxxas 2056 High-Torque Waterproof Servo   High-Torque Waterproof Servo 80 oz-in torque Transit time 0.23 sec/60°   Replacement Part For Bandit BIGFOOT No. 1 Officially Licensed Replica Bigfoot Officially Licensed...

This is the Traxxas Engine Connecting Rod for TRX 2.5, 2.5R, and 3.3 Nitro Engines.FeaturesAluminum constructionPre-installed bushingSpecificationsLength: 37mm (1.46")Thickness: 3mm (0.12")Fits:Jato 3.3Nitro 4-TecNitro Rustler 2.5Nitro SlashRevo 2.5 & 3...

These are the replacement GTR Shock Retainers for the Traxxas Nitro Revo Monster Truck. FEATURES:Nylon ConstructionBlack in Color INCLUDES:Two Black Nylon GTR Shock CapsTwo Black Nylon GTR Spring AdjustersTwo Black Nylon GTR Spring RetainersTwo Black...

This is a set of six Traxxas 3mm x 18mm Button-Head Machine Screws for the Jato 2.5 and 3.3 trucks. Replacement part forDrag Slash 1967 Chevrolet C10 TruckDrag Slash Ford Mustang 5.0Ford F-150 RaptorFord Fiesta ST RallyHoss 4X4 VXLJatoMaxxRustler 4X4...

This is a package of six Traxxas 4x12mm Button-Head Hex Machine Screws. Replacement part for these modelsDrag Slash 1967 Chevrolet C10 TruckDrag Slash Ford Mustang 5.0E-Revo VXL BrushlessFord F-150 RaptorFord Fiesta ST RallyHoss 4X4...

These are the Traxxas 3x10mm Buttonhead Hex Machine Screws. Each package includes six screws. These are used across many of the Traxxas vehicles.Fits1/10 E-Revo Brushed1/10 E-Revo Brushless1/10 Rally1/10 Summit1/16 E-Revo Brushed1/16 E-Revo VXL...

These are the 3x6mm Flathead Machine Screws from Traxxas.FeaturesSteel constructionBlack in colorIncludesSix 3x6mm Flathead Machine ScrewsSpecificationsLength: 6mmDiameter: 3mm

These are the Traxxas 3x20mm Buttonhead Hex Machine Screws. Each package includes six screws. These are used in many different Traxxas vehicles.Replacement part forBandit VXLDrag Slash 1967 Chevrolet C10 TruckDrag Slash Ford Mustang 5.0Ford F-150...

This is a set of Traxxas Rod ends (12)/ hollow balls (12) Set of twelve rod ends come assembled with hollow balls. Replacement Part ForDrag Slash 1967 Chevrolet C10 TruckDrag Slash Ford Mustang 5.0Ford F-150 RaptorFord F-150 Raptor R 4X4Hoss 4X4...

This is a set of Traxxas Jato 2.5 andThese are the Left and Right Gearbox Halves for the Traxxas Nitro Jato Stadium Truck. FEATURES:Nylon constructionBlack in color INCLUDES:One Left Gearbox HalfOne Right Gearbox Half REQUIRES:Assembly onto Vehicle

This is a Traxxas Jato 2.5 and 3.3 Roll Hoop and EZ Start Plug Mount.

This is the Traxxas TRX 3.3 Engine Wrist Pin with Wrist Pin Clips. This is a replacement wrist pin for the 3.3 engine in vehicles like the Jato 3.3, Nitro 4-Tec, Nitro Slash, Revo 3.3, Slayer Pro, and T-Maxx 3.3.

This is a pair of RPM Blue Black Suspension A-Arms for the Traxxas Jato 2.5 and 3.3 trucks. These are very strong, and they include a lifetime warranty through RPM against breakage. If you break one under normal use, just send it in to RPM for a free...

This is the Team Integy 58-Tooth Steel Spur Gear for the Traxxas Jato 2.5, 3.3, and T-Maxx 3.3 trucks. This is MUCH stronger than a plastic spur gear. The Integy spur gears feature color-coded rings to allow easy identification. Going to a smaller...

This is a package of three Air Filter Foam Inserts for the Traxxas 2.5 engine. FEATURES:Constructed of foam and pre-oiled to trap dirt INCLUDES:Three Air FIlter Inserts for the Traxxas 2.5 engine REQUIRES:Installing in air filter boot on...

This is the Traxxas 58mm Camber Links, Turnbuckles (Assembled with Rod Ends and Hollow Balls) (2) 58 mm camber links come assembled with rod ends and hollow balls. Replacement Part ForFord F-150 Raptor R 4X4Hoss 4X4 VXLJatoRustler 4X4 UltimateRustler 4X4...

These are the BellCrank Bushings for the Traxxas Nitro Jato Stadium Truck. FEATURES:Nylon constructionWhite in color INCLUDES:Four 4mm x 7mm x 2.5mm White Plastic Bushings REQUIRES:Assembly onto Vehicle

This is a pair of Traxxas 5x10x4mm ball bearings.  These are used in the clutch bells of many of the Traxxas vehicles. FeaturesThe bearings are constructed of stainless steel Includes2- Bearings Specs5x10x4mm

This is a pack of Traxxas Black 90-Degree Angled Body Mounting Clips (10 clips).  The angled design helps make it easier to remove and install them from the body posts. These can be used as clips on numerous vehicles for the body and other places...

This is the Traxxas Curved Tip Heavy Duty Body Scissors for cutting and trimming polycarbonate RC bodies. To do a good job on a custom body, the right tools are a must. Having both a curved tip and straight tip (Traxxas part TRA3431) scissors in your...

This is the Traxxas Straight Tip Heavy Duty Body Scissors for cutting and trimming polycarbonate RC bodies. To do a good job on a custom body, the right tools are a must. Having both a straight tip and curved tip (Traxxas part TRA3432) scissors in your...

This is a pair of Traxxas Replacement Wheelie Bar Rubber Tires for the Traxxas aluminum aftermarket wheel sets (part 5186 & 5186A) used on many vehicles.Includes: Two Rubber Tires for the Wheelie BarSpecificationsOuter Diameter: 1.1" (29mm)Inner...

These are the Traxxas 90-Degree Body Clips. These are a smaller size, typically used to hold down receiver covers, battery hold-downs, bodies on smaller trucks, etc.FeaturesMetal ConstructionSilver in ColorBent for Easy RemovalIncludesTen Bent Silver...

This is the Traxxas Standard Size Body Clips (12) - Standard-duty body clips   Replacement part for1/16 E-Revo VXL1/16 E-Revo1/16 Slash 4WD1/16 SummitBandit VXLBanditBIGFOOTJatoNitro RustlerRevoRustler VXLRustlerSlayer Pro 4X4Stampede...