These are the Traxxas Blue Aluminum 17mm Splined Hex Wheel Hubs with Pins and Set Screws. This includes four hubs, four pins, and four set screws.  17 mm blue-anodized aluminum wheel hubs combine high-profile looks with superior strength. The...

This is the Traxxas Unlimited Desert Racer 51-Tooth Center Differential Spur Gear. The 51-tooth differential spur gear (32-pitch) lets you fine-tune the performance of your Traxxas model. Changing gear ratios can help balance acceleration and top speed...

These are the Traxxas Unlimited Desert Racer Left and Right Axle Carriers.Stock Replacement OnUnlimited Desert Racer (UDR)

This is the Traxxas Unlimited Desert Racer Front Skidplate and Steel Support.Stock Replacement OnUnlimited Desert Racer (UDR)

This is the Traxxas Unlimited Desert Racer Single 4S LiPo BAttery Jumper, which allows the Traxxas VXL-6s ESC to run on single 4S 14.8V LiPo battery pack.Accessory Part ForUnlimited Desert Racer (UDR)

This is the Traxxas X-Maxx and XRT Temperature and Voltage Sensor.Accesory Part For X-Maxx XRT

This is the Traxxas E-Revo 2.0 Transmission Skidplate and Cover.Stock Replacement OnE-Revo 2.0

These are the Traxxas 12x21x5mm Blue Rubber Sealed Ball Bearings (2) used on the E-Revo 2.0 trucks.Stock Replacement OnE-Revo 2.0

This is pair of Traxxas Red Rear Springs (2.9 rate) for use with XXL Ultra ShocksStock Replacement On1/10 Monster Jam TrucksCraniacT-Maxx 3.3Accessory Part For1/10 Monster Jam TrucksNitro StampedeRustler VXLRustler XL-5SkullySlash 2WDSlash 2WD Ford...

This is the Traxxas Bandit Hawaiian Painted Body. This is a direct fit for the Bandit XL-5 and VXL buggies. Is it time to upgrade your Bandit with an all-new look? These tough polycarbonate bodies feature the hottest ProGraphix paint with pre-applied...

This is the Traxxas 4-Tec 2.0 Ford GT Red Pre-Painted Body with Decals. This body is even pre-cut, making for quick final installation!Note: Tail lights, exhaust tips, & mounting hardware (Traxxas part #8314) are not includedFits4-Tec 2.0

This is the Traxxas Slash 2WD Pink Rear Bumper and Mount. This fits all versions of the Slash 2WD short-course truck.FitsSlash 2WD Ford RaptorSlash 2WD VXLSlash 2WD XL-5

These are the TraxxasBoat Blue Aluminum Drive Strut Mounts Blue-anodized aluminum drive strut mounts (2) Replacement Part ForDCB M41 Widebody Accessory Part ForDisruptor

This is the Traxxas Pink Aluminum Steering Bellcrank Set for the Slash 2WD, Rustler, and Bandit vehicles. These will fit XL-5 brushed and VXL brushless trucks.If installing on a vehicle that currently has a servo saver built into the bellcrank, we...

This is the Traxxas 22-Tooth 48-Pitch Pinion Gear with Set Screw. This designed for use with the 4-Tec 2.0, but can also be used with any vehicle that could use a 22T 48-pitch pinion.Fits4-Tec 2.0

This is a pair of Pro-Line Badlands MX43 Pro-Loc Tires for Pro-Loc X-Maxx Wheels. These tires stand a massive 8.3-inches tall and are constructed with an ultra-durable anti-ballooning tire compound to hold up better under the extreme performance of the...

This is the Integy Steel Roll Cage for Traxxas T-Maxx 3.3 model 4907 and 4908 series trucks. Add some real-world strength to your vehicle with this Steel Roll Cage add-on. The cage is welded into one piece for strength and durability. Finished in the...

These are the the Vanquish Incision #8 Wheel Hubs for use with Incision wheels. This set features an offset of 0.825" and provides a track width change of +0.80" (+20.3mm) from the stock #4 0.425" Incision hubs.Features Compatible with Incision...

These are the the Vanquish Incision #5 Wheel Hubs for use with Incision wheels. This set features an offset of 0.525" and provides a track width change of +0.20" (+5.1mm) from the stock #4 0.425" Incision hubs.Features Compatible with Incision...

These are the the Vanquish Incision #4 Wheel Hubs for use with Incision wheels. This set features an offset of 0.425" and match the stock hubs included with Incision wheels.Features Compatible with Incision wheels* Sold in pairs Increments of .100...

This is the RPM Traxxas X-Maxx Low Visibility Wheelie Bar. This must be used with the RPM81762 rear bumper mount. With the mount, it can be used on both X-Maxx 8S and 6S trucks.RPM Low Visibility Wheelie Bars are designed to take the stress off of the...

This is the Traxxas 4-Tec 2.0 Motor Plate. This fits all 4-Tec 2.0 cars, including the Ford GT and Mustang GT.Stock Replacement On4-Tec 2.0 VXL Chassis4-Tec 2.0 XL-5 Chassis4-Tec 2.0 Ford GT4-Tec 2.0 Ford Mustang

These are the Traxxas 4-Tec 2.0 Inner Drive Cups and Screw Pins. These fit all versions of the 4-Tec 2.0, including the Ford GT and Mustang GT.Includes2 inner drive cups2 screw pinsFits4-Tec 2.0

These are the Traxxas 4-Tec 2.0 Left and Right Stub Axle Carriers. These fit all versions of the 4-Tec 2.0, including the Ford GT and Mustang GT. Replacement Part For4-Tec 2.0 AWD Chassis4-Tec 2.0 VXL AWD ChassisChevrolet Corvette StingrayFactory Five...

These are the Traxxas TRX-4 Scale Crawler 2-Speed Drive Hub, Shift Dog, Shift Fork, Shaft Seal, and 2-Speed Linkage.Stock Replacement OnTRX-4 Crawler KitTRX-4 Ford BroncoTRX-4 Land Rover DefenderTRX-4 TacticalAccessory Part ForTRX-4 SportNote: Accessory...

These are the Traxxas TRX-4 Crawler Red Bumper D-Rings and Mount Screws. This includes four D-rings and four 2.0x12mm screws.FitsTRX-4

These are the Traxxas TRX-4 Crawler Grey Bumper D-Rings and Mount Screws. This includes four D-rings and four 2.0x12mm screws.FitsTRX-4

These are the Traxxas 5x8x2.5mm Black Rubber Sealed Ball Bearings (2). Each package includes two bearings. Pair of 5x8x2.5 mm black rubber seal ball bearings. A step above blue-seal bearings, black-seal bearings offer an even tighter seal for ultimate...

These are the Traxxas 2.5x16mm Cap-Head Hex Machine Screws (6). Each package includes six screws.FitsTRX-4

This is the Hot Racing Chassis Cover Dirt Guard for Traxxas X-Maxx 6S and 8S trucks. The chassis cover attaches to the chassis with easy-to-apply hook and loop tape; has zipper chassis access; and uses a breathable Nylon mesh to repel water and protect...

This is the Hot Racing Aluminum 100mm HD Big Bore Shock Set with eight shocks for the Traxxas T-Maxx 2.5, T-Maxx 3.3, E-Maxx 16.8V, and E-Maxx Brushless trucks. These can also be used with other shocks requiring 100mm shocks.FEATURES:- CNC machined...

This is the Traxxas Assembled Torque Biasing Center Drive with 17x26x5 Bearings (2). Replacement Torque-Biasing Center Drive comes complete and ready to install. Fits 7727X bulkheads only Includes17x26x5 mm bearings (2). Replacement part forX-Maxx...

This is a pair of Traxxas X-Maxx 8S-Rated Maxx AT Tires with Foam Inserts. Each package includes two tires and two foam inserts. Huge Maxx AT 8.0x4.0" tires offer ferocious grip with an aggressive tread pattern. Tires are sold as a left and right...

This is the Traxxas Blue Aluminum Stub Axle.  Add a touch of style to your X-Maxx or XRT with these brightly-anodized aluminum stub axles.  For use with 8s-spec heavy duty driveshaft (#7750X) only. Replacement Part For These Models: X-MaxxXRT

This is a pair of Traxxas X-Maxx GTX 1.346 Rate Springs. These come in packages of two springs. This is a firmer spring rate than stock.Features Steel construction Firmer than stock 1.055 rate Natural (unpainted) finish Includes: Two 1.346 Rate...

This is the Traxxas Aton Front Left & Right LED Lens (Green). This is Traxxas part number 7954Part Number: 7954 / TRA7954FitsAtonAton PlusMore detail coming soon! Please check your vehicle manual to confirm vehicle fitment, or contact us if you have any...

This is the Traxxas Aton Rotor Blade Set (2) (Orange) w/Screws. This is Traxxas part number 7930Part Number: 7930 / TRA7930FitsAtonAton PlusMore detail coming soon! Please check your vehicle manual to confirm vehicle fitment, or contact us if you have...

This is the Traxxas Aton Canopy Roll Hoop (Green). This is Traxxas part number 7921Part Number: 7921 / TRA7921FitsAtonAton PlusMore detail coming soon! Please check your vehicle manual to confirm vehicle fitment, or contact us if you have any questions.

This is the Traxxas Front & Rear Driveshaft Assembly 6061-T6 Aluminum (Blue-Anodized) (2) Replace the standard composite driveshafts in your 1/18 scale LaTrax Prerunner or Teton with these aluminum driveshafts. Made from tough 6061-T6 aluminum and...

This is the Traxxas Bumpers, front (1)/ rear (1). This is Traxxas part number 7135Part Number: 7135 / TRA7135Fits1/16 E-Revo Brushed1/16 E-Revo VXL BrushlessMore detail coming soon! Please check your vehicle manual to confirm vehicle fitment, or contact...