This is the Traxxas 20-Tooth Idler Gear and Shaft for the E-Maxx, E-Maxx Brushless, 1/10 E-Revo, 1/10 E-Revo Brushless, and 1/10 Summit trucks.IncludesOne 20 Tooth Idler GearOne 5x18mm Idler Gear ShaftSpecificationsOutside Diameter: .86" (22mm)Inside...

This is the Traxxas Black Rear Springs for use on the XX-Long Ultra Shocks used on vehicles like the Slash 2WD, Rustler, Stampede 2WD, Stampede 4x4, and others.Accessory Part ForBIGFOOT No. 1 Officially Licensed ReplicaFord F-150 RaptorHoss 4X4 VXLNitro...

This is the Traxxas Green Wheelie Bar Mount with Hardware for Slash 2WD, Rustler, Stampede 2WD, and Bandit vehicles.IncludesOne wheelie bar mountHardwareInstructions Fits1/10 Monster Jam TrucksBandit VXLBandit XL-5CraniacRustler VXLRustler...

This is a set of Traxxas 3x15mm Flat-Head Hex Drive Machine Screws. Each package includes six screws.Includes: Six 3 x 15mm Flathead Hex Machine Screws Replacement Part ForBandit VXLDrag SlashFord F-150 RaptorFord Fiesta ST RallyHoss 4X4 VXLMaxxRustler...

These are the Traxxas 3x10mm Cap-Head Hex Machine Screws. Each package includes six screws.Fits1/10 E-Revo Brushed1/10 E-Revo Brushless1/10 Monster Jam Trucks1/10 SummitBandit VXLBandit XL-5CraniacFunny CarRevo 3.3Rustler XL-5SkullySlayerSlayer...

This is a pair of Traxxas Tracer 2.2" Chrome Front Wheels for the Bandit XL-5 and VXL buggies. These wheels have a slot in the hub to slide over the axle pins.FEATURES:Chrome 5-spoke designFits standard 2.2" truck tiresINCLUDES: Two front 2.2" 5-Spoke...

This is a pair of Traxxas Bandit Rear Alias 2.2" Tires Mounted on Tracer Chrome Wheels. These are a soft-compound tire with foam inserts, pre-mounted and glued on chrome wheels.These are a direct fit on the rear of the Bandit XL-5 and Bandit VXL buggies.

This is a pair of Traxxas Bandit Alias 2.2" Rear Tires with Foam Inserts. These are a soft-compound tire, for use with 2.2" wheels on the Traxxas Bandit XL-5 and VXL buggies.

This is a tube of Traxxas Marine Grease (30cc) for use on RC boats like the Traxxas Spartan. This is a must-have accessory to keep the flexshaft of your boat in good condition and performance at its peak! Use marine grease liberally on your propeller...

This is the RC4WD Wired Winch Control Unit offered to allow operation function from your radio and receiver. This will allow you to control a winch with your remotes third channel. This is recommended for use with the RC4WD Warn 1/10 9.5cti Winch...

These are the RPM Black Revolver 2.2/3.0 Front Wheels for the Traxxas Slash 2WD Electric Short Course trucks with Spline Drives. These feature splined drives instead of hexes for incredible strength. Spline adapters are included.The most popular RPM...

This is the RPM Green Axle Carriers for the Traxxas 1/16 E-Revo, 1/16 Slash, and 1/16 Summit. This fits brushed and VXL brushless versions.There is very little that can be as frustrating on an R/C vehicle as slop in the suspension system. In the case of...

This is a pair of Traxxas GTR Shock Springs (XX-Long 1.004 Blue) for 1/10 Slash Ultimate & Platinum trucks with GTR shocks. Shock springs for 1/10 scale XX-long GTR shocks use high-quality spring steel with a durable white powder-coated finish. GTR...

This is a pair of Traxxas GTR Shock Springs (Long .623 Orange) for 1/10 Slash Ultimate & Platinum trucks with GTR shocks Shock springs for 1/10 scale long GTR shocks use high-quality spring steel with a durable white powder-coated finish. GTR springs...

This is the Traxxas Center Harness and Wire Clip for the LED Lights used on the Summit 1/10 truckFeatures:JST ConnectorsIncludes:One Center HarnessOne Wire ClipThree Zip Ties

This is the optional Clear Body for the Traxxas Summit VXLFeaturesTrimmed and ready to paintIncludesOne Clear Body for the Traxxas 1/16 Summit VXLRequiresPolycarbonate safe spray or brush-on paintGrille and decalsSpecificationsLength: 11.4" (291mm)Width:...

This is the Chassis for use on the Traxxas 1/16 E-Revo and Slash VXL Vehicles.FeaturesNylon constructionGrey in colorSpecificationsLength: 245mm (9.6")Width: 107mm (4.2")Height: 40mm (1.6")

These are the Traxxas Mounts for the RPM Telemetry Sensor for Nitro Engines. RPM sensor mounts allow you to mount an RPM sensor to your nitro engine. IncludesThree different plastic mountsTwo plastic spacersTwo flat washersTwo split washersTwo hex socket...

These are the Traxxas All-Star Chrome Wheels with Talon Tires Talon tires provide "just-right" grip and handling on a wide variety of surfaces. The tires come mounted with foam inserts and pre-glued to tough 2.8″ All-Star 5-spoke chrome wheels. The...

These are the 4x15mm Round Head Machine Screws from Traxxas.FeaturesSteel construction Silver in colorIncludesSix 4x15mm Round Head Screws SpecificationsLength: 15mm (0.59")Width: 4mm (0.16")

These are the optional Traxxas Differential Output Yokes for the E-Maxx, T-Maxx .15, 2.5, and 3.3 trucks. FEATURES: Features thicker plastic for long life and durability These diff yokes are more rigid than the stock yokes Black in color INCLUDES:Two...

This is the Traxxas Spartan Stuffing Tube with Nylon Liner. Replacement stuffing tube assembled with liner Features: Brass and nylon construction Includes: One Assembled Stuffing Tube Specifications:Length: 10.6" (270mm)Outside Diameter of Stuffing Tube:...

This is a pair of Traxxas Aluminum Bellcrank Posts for the T-Maxx and E-Maxx trucks. These bellcrank posts hold the steering bellcranks to the chassis. The link connects the steering bellcrank to the servo saver. Features: Stock aluminum...

This is an optional Traxxas Large Knurled Flywheel for use with Starter Boxes. Features: Large knurles to be gripped by rubber starter wheels Two pin aluminum construction Vent holes drilled to keep clutch shoes cooler Includes: One 40mm...

This is the Traxxas replacement piston and sleeve for the TRX Pro .15 engines. Features: ABC (Aluminum piston with a Brass sleeve or liner that is Chrome plated) Matched set with oil ring Includes:1 Piston1 Sleeve (liner)

These are Traxxas Steering Bellcranks and Draglinks for the Traxxas Rustler, Stampede, and Bandit. Left and right steering bellcranks with drag link Features: White Plastic Construction Replacement Part ForBandit VXLBanditFord F-150 RaptorNitro...

These are Traxxas 3x10mm Hex Screws (6). Features: Steel construction cap head with hexagon socket drive insert Metal lock washers Includes:(6) Screws(6) Lock Washers(1) Hex Wrench Specifications:Screws:Diameter: 3mmLength: 10mm Lock Washers:Inner...

This is the RPM True-Track Rear A-Arm Conversion in Black for all versions of the Traxxas Revo 2.5, 3.3, E-Revo, and E-Revo Brushless. This setup is lighter, stronger, and eliminates the bump steer of the rear end! The RPM True-Track Rear A-arm...

These are the Traxxas Slash 4X4 Progressive Shock Springs: Front, -20% Rate, Orange (2) Features Custom wound for Slash 4X4 Progressive-rate design allows small-bump compliance without compromising big-hit capability Durable powdercoated...

These are Teflon Washers from Traxxas. This will work on the Nitro Rustler. FEATURES Teflon washers INCLUDESTen Teflon washers REQUIRESTraxxas Nitro Rustler SPECS6x9.5x.5

This is the Traxxas Plastic Washers,Wht: ST, RU, BA(6)

This is the Integy Blue Aluminum Evolution Suspension Conversion Kit for the Traxxas Rustler XL-5 and VXL trucks. Features: Aluminum construction Blue in color Includes: Shock towers-front and rear Four hex wheel hubs with...

This is the Integy Type II Blue Aluminum Rear Shock Tower for the Traxxas Stampede 2WD XL-5, Rustler and Slash 2WD FEATURES Blue in color Fits rear of vehicle INCLUDESOne Type II Aluminum Rear Shock Tower REQUIRESInstalling on chassis SPECSThickness: 0...

These are a set of 2.2" Mounted Satin Chrome Wheels and Tires for the Traxxas Slash, TRAC43**. FEATURES:Front tires2.2" Satin Chrome WheelsOff-Road Racing Tires5 spoke design INCLUDES:Two 2.2" mounted Off-Road Racing Tires, Satin Chrome Wheels Foam...

This is an optional Wheelie Bar Mount for all versions of the Traxxas Revo. FEATURES:Constructed of hardened plastic, black in colorInstalls at rear of chassis to hold wheelie bar arm and wheels in place INCLUDES:Assembled optional Wheelie Bar Mount with...

This is the optional Extended Battery Hold Down Set for the Traxxas E-Maxx Series. FEATURES:Composite nylon construction, black in colorInstall one way and you can secure battery packs up to 21mm in height flip it over and install for battery packs up...

This is the Robinson Racing Xtra Hard 5mm Bore Steel 12-Tooth 1.0 Module Pinion Gear.  This works in brushless setups for the Traxxas Revo 2.5, 3.3, and T-Maxx 3.3, and it also works with most 1/8 scale brushless conversions for Associated,...

This is the Robinson Racing Xtra Hard 5mm Bore Steel 11-Tooth 1.0 Module Pinion Gear.  This works in brushless setups for the Traxxas Revo 2.5, 3.3, and T-Maxx 3.3, and it also works with most 1/8 scale brushless conversions for Associated,...

This is the 1st Speed Gear 32T for the Traxxas Nitro Jato Stadium Truck. FEATURES:Nylon constructionBlack in color INCLUDES:One 1st Speed Gear 32TOne Input Gear 14TOne Threaded Pin Shaft REQUIRES:Assembly onto Vehicle

This is Traxxas Jato 2.5 and 3.3 Assembled Composite Tuned Pipe.  This features molded composite construction and includes a rubber header gasket. Replacement composite tuned exhaust pipe Replacement Part ForJatoTRX 2.5