Telluride

These are the Traxxas 3x15mm Buttonhead Hex Machine Screws. Each package includes six screws. These are used across many different Traxxas vehicles.Replacement part for1/16 E-Revo VXL1/16 E-Revo1/16 Slash 4WD1/16 Summit4-Tec 2.0 AWD Chassis4-Tec 2.0 VXL...

These are rubber cap diaphragms for Traxxas plastic shocks. These also work well with some Associated aluminum shocks. Replacement Part For4-Tec 2.0 AWD Chassis4-Tec 2.0 VXL AWD ChassisBandit VXLBanditBIGFOOT No. 1 Officially Licensed ReplicaChevrolet...

This is a Package of 3x12x5mm Shoulder Screws for many Traxxas Vehicles. Set of six 3x12 mm shoulder screws (shock attachment screws) with Phillips-drive heads. SPECSLength: 12mm (.47")Diameter: 3mm (.12")Thread Length: 5mm (.20") Replacement Part...

This is the Traxxas Wheel Hubs hex (blue-anodized, lightweight aluminum) (2)/ axle pins (2) These 12 mm aluminum hex wheel hubs are both lightweight and tough as nails with brilliant blue anodizing. *Includes axle pins (2) Accessory part forDrag Slash...

This is the Traxxas Slipper clutch - complete.  The slipper clutch comes completely assembled and ready to install into your 1/10 scale 4X4 vehicle. The slipper clutch can be used as a standard replacement for existing clutches, or as an upgrade for...

This is a 48P, 76T Spur Gear for models with Traxxas Torque Control Slipper Clutch. FEATURES:48 pitch76 toothDesigned for models with a slipper clutch.Black plastic construction INCLUDES:One spur gear SPECS:Pitch:   48Tooth:   76

This is the Traxxas Stub axles, rear, heavy duty (2)/pins (2). This is Traxxas part number 6853XPart Number: 6853X / TRA6853XFits1/10 Monster Jam Trucks1/10 RallyCraniacNitro SlashRustler VXLRustler XL-5SkullySlash 2WDSlash 2WD Ford RaptorSlash 2WD...

These are the Hot Racing Carbon Fiber Long Slipper Clutch Pads with 25% more surface area than stock pads, for use in place of Traxxas 5352 or 5552 pads. These fit Traxxas Bandit, E-Maxx, E-Revo, Jato 3.3, Rally VXL, Revo 3.3, Rustler, Slash 2WD, Slash...

This is a set of 12 Traxxas 3mm Locking Nuts. These feature chrome nylon locking nuts. Replacement part for1/16 E-Revo VXL1/16 E-Revo1/16 Slash 4WD1/16 SummitBandit VXLBIGFOOT No. 1 Officially Licensed ReplicaDCB M41 WidebodyDrag Slash 1967 Chevrole C10...

This is a Traxxas Steel Slipper Clutch Shaft for the Slash, Rustler, and Stampede vehicles. Features: Steel construction Roll pin pre-installed Includes: One slipper clutch set Specifications:Length: 1.98" (50mm)Diameter: .21" (5mm)

This is pack of Traxxas DC Charger 5-Amp Fuses (2). These are replacements for use in the 2-amp and 4-amp DC 12-volt cigarette-lighter style quick chargers included with many of the Traxxas electric and nitro vehicles.Fits Traxxas charger model 2974,...

This is a 31 Tooth, 48 Pitch Pinion Gear with Set Screw from Traxxas. FEATURES:Steel construction, silver in color INCLUDES:One 31 Tooth, 48 Pitch Pinion GearOne 3x4mm Set Screw (1.5mm hex size) REQUIRES:Installation SPECS:Length: .42" (10.5mm)Inside...

This is a shock rebuild kit for 2 Traxxas black plastic shocks. Includes:4 E-clips2 C-clips2 O-rings8 Washers2 Diaphrams Replacement Part For4-Tec 2.0 AWD Chassis4-Tec 2.0 VXL AWD ChassisChevrolet Corvette StingrayFord F-150 Raptor R 4X4Ford Fiesta ST...

This is a pair of Traxxas 5x8x2.5mm Blue Rubber Sealed Ball Bearings. These fit a large number of Traxxas 1/10 and 1/16 scale vehicles.Includes: (2) 5X8mm ball bearingsSpecificationsInside diameter: 5mmOutside diameter: 8mmWidth: 2.5mmReplacement part...

This is set of Traxxas Rod Ends (16 long & 4 short) with 18 hollow balls and two ball screws. These are used on most Traxxas vehicles.Includes:4 short rod ends (17mm)16 long rod ends (19mm)2 ball screws18 hollow ball connectors Replacement Part...

This is the Diff Carrier/Gasket Set Replacement differential carrier includes X-ring gaskets (2), ring gear gasket, and 6x10x0.5 mm washer. FEATURES:Plastic Diff CarrierBlue Rubber Shaft GasketsBlack Rubber Diff Carrier GasketsGray Teflon...

This is a set of Traxxas 3mm Hardened Set Screws, also known as grub screws. Each package includes 12 set screws. Set of twelve 3 mm hardened steel grub screwsReplacement part for these models1/16 E-Revo VXL1/16 E-Revo1/16 Slash 4WD1/16 SummitBanditDCB...

This is the Traxxas TQ 2.4GHz 3-Channel Micro Receiver for use with the TQ 2.4GHz transmitter. The TQ 2.4GHz micro receiver uses an integrated LINK button for fast and easy binding. A two-color LED indicates power-on and bind status for fool-proof...

This is the Slipper Clutch Rebuild Kit for the Traxxas Vehicles. The slipper clutch rebuild kit refreshes the standard-duty slipper clutch with a new disc, friction pads (3), springs (2), dowel pin, 4 mm locknut and 5 mm locknut. Fits: 5556 pressure...

This is a set of four Traxxas Green-Anodized Aluminum 4mm Lock Nuts with a Flanged and Serrated surface.Features May be used in any application requiring this size locknut Serrated rear section ensures sure grip Includes: Four 4mm Flanged...

This is the Traxxas Antenna Cap Set with Antenna Spool. The antenna spool is used for wrapping excess antenna wire before inserting it in the antenna tube to prevent wire from hanging out the end of the tube, preventing damaged antenna wires caused by...

These are the Traxxas Blue Aluminum Wheelie Bar Wheels and Rubber Tires for the Traxxas Wheelie Bars (model 4975 and 3678) for all Traxxas T-Maxx, E-Maxx, Jato, Slash 2WD, Slash 4x4, Rustler, Stampede 2WD, Stampede 4x4, and Bandit series vehicles.Traxxas...

These are the Hot Racing Carbon Fiber Stock Length Slipper Clutch Pads, for use in place of Traxxas 5352 or 5552 slipper pads. These fit Traxxas Bandit, E-Maxx, E-Revo, Jato 3.3, Rally VXL, Revo 3.3, Rustler, Slash 2WD, Slash 4X4, Slayer Pro 4X4,...

This is the Long Temperature and Voltage Sensor for the Traxxas TQi system. To read voltage on electric vehicles, this must be used with the Traxxas part TRA6541 Power Tap. The temperature/voltage sensor plugs directly into your TQi receiver and power...

This is the Traxxas Velineon 3500 4-Pole Brushless Waterproof Motor. This is the replacement motor found in many of the 1/10 brushless trucks, designed for use with the VXL-3s ESC. See full list of compatible trucks below.The Velineon 3500 Brushless...

This is the Traxxas EZ-Peak Plus 4s, 8-Amp Auto-iD NiMH/LiPo with iD Auto Battery Identification Charger. With up to 8-amps of output it will charge 2S-4S LiPo, and 5-8 cell NiMH battery packs. The EZ-Peak Plus 4s, 8-Amp charger works with the Traxxas iD...

This is the Traxxas aluminum (Green Anodized Shock Caps Shock caps, aluminum (green-anodized) (4) (fits all Ultra Shocks)Aluminum shock caps are great way to boost the durability and style of any Traxxas vehicle equipped with Ultra Shocks. The machined...

This is a pair of the Traxxas XX-Long Ultra Shocks (part 3762A) for use on a wide variety of Traxxas vehicles, including the Bandit, Rustler, Stampede 2WD & 4x4, Slash, Hoss, T-Maxx, and more. Traxxas oil-filled Ultra Shocks utilize X-rings for a...

This is a set of Traxxas Red Aluminum 4mm Flanged Serrated Nuts (4).  These are used as wheel nuts and lock nuts on many Traxxas models. Accessory part forDrag Slash 1967 Chevrolet C10 TruckDrag Slash Ford Mustang 5.01/16 E-Revo VXL1/16 E-Revo1/16...

This is a pair of Traxxas 6x12mm Ball Bearings with Rubber Dirt Shields. Pair of 6x12x4 mm blue rubber seal ball bearings. Blue-seal ball bearings keep dust and grime out for less maintenance, smoother running and less friction...

This is a 23 Tooth 48 Pitch Pinion Gear By Traxxas FEATURES:Pinion gear with set screw, Silver in color INCLUDES:(1) 23 Tooth 48 Pitch Pinion Gear(1) One 4mmx2mm set screw REQUIRES:Installation SPECS:Outer Diameter: 14mm (9/16")Inner Diameter: 11mm...

These are the Steering Blocks for the Traxxas Slash 4x4. Replacement part forFord Fiesta ST RallyHoss 4X4 VXLRustler 4X4 VXLRustler 4X4Slash 4X4 VXLSlash 4X4Stampede 4X4 VXLStampede 4X4 Accessory part forSlash 4X4 Ultimate

This is the GPM Racing Blue Aluminum Steering Bellcrank and Servo Saver for Traxxas 1/10 Slash 4x4, Rustler 4x4, Stampede 4x4, 1/10 Rally, and Telluride trucks. These are made of 6061-T6 aluminum for strength and durability. They look great, and...

This is the 16 Tooth 48 Pitch Pinion Gear from Traxxas. FEATURES:Steel construction INCLUDES:16 Tooth 48 Pitch Pinion Gear with set screw REQUIRES:Installing on motor shaft SPECS:Number of Teeth: 16TPitch: 48Inner Diameter: 0.12" (3mm)

This gear is a steel pinion gear in 48 pitch Features:Brass pinion gear Includes:1 gear and 1 set screw Specs:Steel, 48 pitch, 25 tooth pinion gear.Shaft length- 3/16"  Gear length- 1/4"  Overall length- 7/16"Shaft diameter- 1/4"  Gear...

These are Traxxas 3x6mm Metal Washers. Each package includes 12 washers. Replacement part forDrag Slash 1967 Chevrolet C10 TruckDrag Slash Ford Mustang 5.0Ford F-150 RaptorFord Fiesta ST RallyHoss 4X4 VXLNitro SlashRustler 4X4 VXLRustler 4X4Slash 2WD...

These are Traxxas 3x8mm Button Head Screws (6). Features: Black steel construction with hex headIncludes: Six screws Replacement part for these models1/16 E-Revo VXL1/16 E-Revo1/16 Slash 4WD1/16 SummitBandit VXLBlastDrag Slash 1967 Chevrolet...

This is the Traxxas Complete Rear Differential for 1/10 4x4 Slash, Hoss, Stampede, Rustler, and Rally.  This complete, pre-assembled diff is a great part to quickly repair a damaged driveline, and a great spare part to have on hand too. The...

This is the Traxxas Steering Bellcrank Set for the Slash 2WD, Slash 4x4, 1/10 Rally, Bandit, Rustler, and Stampede 4x4 vehicles. Features: Composite nylon construction Replaces a worn or damaged bellcrank set Includes:One Left Bellcrank LowerOne Left...

This is a set of Traxxas Long Rod Ends with Hollow Ball Connectors. Each package contains six rod ends and six hollow balls.Fits1/10 Monster Jam Trucks1/10 RallyBandit XL-5CraniacE-MaxxNitro 4-TecNitro RustlerNitro SlashNitro SportNitro StampedeRustler...