This is the Futaba 3PK Super Black Pistol Grip 3-Channel Transmitter.  This model does not include a module, servos, or receiver, allowing the driver to choose what best suits their needs.

FEATURES:

Upgrades over the original 3PK include:

• Expanded Driver Menu, with "New Driver" "Race-Ready" and "Expert" menus and a mid-level "Big" menu for drivers of 1/5 scale and larger vehicles
• Redesigned Keypad, with jog button giving access to four different directions by moving button left, right, up or down and then pushing in
• Vibrating Alert System, functions like a timer to let driver know when to bring a nitro car in for a pit stop or check battery life of an electric model
• Increased Model Memory, 20 models also compatible with CAMPac module that adds another 10 models
• Throttle Mode Select, choice of two servo neutral points 70/30 for nitro models and 50/50 model for electrics

Features unchanged from the original 3PK include:

• APA (Advanced Positioning Adapter) for customizing balance and wheel position
• Large Backlit LCD Screen with adjustable contrast and 128 x 64 resolution
• "Direct Select" single button access to 8 preassigned functions
• Adjuster feature restores compromised settings to factory default
• Assignable switch and dial functions
• 10 Digit Model and user naming: English or Japanese characters
• PCM/PPM/HRS Selectable with 3-ch adjustable FailSafe for PCM/HRS
• 3 Function selection modes (New User, Race Ready Driver and Expert provide 1/2/3 menus of features for just the right fit!) PLUS the direct selection 2-key menu to up to 6 functions
• Steering Dual Rate and Dual Rate 2, both adjustable while driving
• Servo display to show all 3 servo positions for easy setup/diagnostic
• Anti-Skid Brake System (ABS) (Keeps tires from skidding, or locking-up, even on gas cars) (with 5 adjustments)
• Throttle Acceleration (decreases lag time before clutch or brakes are engaged)
• Steering and throttle exponential (3 forward expo types) end point adjustments for all 3 channels (EPA/ATV)
• Steering and Throttle servo speed limiters
• Brake mixing for 1/5th scale cars with separate front and rear brakes
• System adjustments for back lighting, pilot lamp color, home display
• Servo Reversing
• Idle-up for easy starts and engine cut for boat engine shut off
• Start (Preset throttle start control. Limits throttle at the beginning of a race to give smoother acceleration and less wheel slip.) (similar to traction control on 3PJS)
• Advanced timer w/100 lap recall & trigger activation
• Trim/dial function selection (can assign different functions to the different trim controls and dials)
• Subtrim adjustments
• Step trim adjustments (allows changing of trims in finer increments)
• Programmable mixing
• Tilt mixing for adjusting the trim tabs with the 3rd channel on boats
• Third channel assignable to any dial/switch/trimmer/mix
• MC-SETUP function for HRS receivers to properly setup ESCs
• ADJUSTER function to manually calibrate trigger and wheel

EQUIPMENT FEATURES:

• Optional DSC cord support for operating receivers without transmitting
• LARGE REAR Facing LCD plus Seven Color Pilot Lamp for easy ID.
• One Year Warranty
• Digital trim with reset
• Left Hand reversible
• Steering wheel tension adjust (can be adjusted without opening radio)
• Trigger stop function (mechanical ATL) and programmable ATL
• Display switch (allows functions to be set without transmitting)
• Audible, adjustable alarm tone and lap counting tones
• Headphone jack for hearing the alarm tones at a noisy track

INCLUDES:
3PK Super Transmitter with antenna
NiCd Transmitter Battery
Switch Harness
Offset wheel adapter and screws
Instruction manual and warranty card
Hex wrench
Battery Charger

REQUIRES:
Transmitter Module
Servos (digital if using in HRS mode)
Receiver
Receiver NiCd battery

SPECS:
Operating System: FM/PPM, HRS_FM or PCM1024 switchable
Transmitting Frequency: 27MHz
Power Supply: 9.6V NiCd
Current Drain: 250mA or less

COMMENTS: This radio is sold without servos and requires digital servos and 6V ONLY when using an HRS receiver. Non-digital servos are fine on PPM/PCM.